48 Results
View results:
Sort by:
Question
How do I determine the stiffness center of my structural system?
Question
Is the Gust-effect (G or Gf) from the ASCE 7‑16 Sect. 26.11 considered in RWIND Simulation?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
Question
How can I create a curved or arched section?
Question
I would like to calculate a hall frame with loads from a crane runway. It is not quite clear to me what the various action categories denote. Can you explain it to me?
Question
Is it possible to perform automatic live load reduction in RFEM or RSTAB per the ASCE, IBC, or NBCC?
Question
How can I determine loads at particular geographic coordinates in the online service "Snow Load, Wind Speed, and Seismic Load Maps"?
Question
How are the location-specific Geo-Zone Tool data queries calculated for the determination of various building loads?
Question
Is it possible to generate wind loads according to DIN EN 13782 with this program?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Question
Why is the load value displayed in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps" different from the value in the corresponding standard in some cases?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Question
I need to define different types of lateral intermediate restrains for a single element in RF-/STEEL EC3. Is this possible?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
Question
How do I superimpose generated equivalent loads from the seismic analysis?
Question
Is it possible to perform design for a timber-concrete composite cross-section?
Question
For the foundation design, I need the results (support reactions) of the design situation for "static equilibrium". How do I get them?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Question
Which result combinations can I design with the RF‑/JOINTS Pro program, and what should I pay attention to?
Question
When designing seismic equivalent loads with a Response Spectra Analysis (RSA) in RFEM, how can I apply the modal response parameters Ie/R according to Sect. 12.9.1.2 in the ASCE‑7‑16 to my results?
Question
Is it also possible to integrate the online service "Snow Load, Wind Speed, and Seismic Load Maps" into external applications?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materials of National Annexes
Where can I find the materials for the corresponding National Annexes in RFEM 6 and RSTAB 9?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5